Blog

How to Build a Drawing Horse

How to Build a Drawing Horse
How to Build a Drawing Horse

A drawing horse is a very functional and useful tool every artist should consider adding to their studio.  It allows you to draw or paint at home in the same manner as you would in a life drawing/painting class. In general horses are used for those who like to sit while they work but they can also be used upright to hold your palette when standing to paint with an easel.

 

 

(these are the proportions)

 

 

 

Here is what I used...

 

 

Drill

15 drywall screws  1- 5/8″
Drill bit
Countersink drill bit
Phillips head drill bit
Tape measure
Ruler
Pencil
Four Pieces of wood 3/4 x 9″or 3/4 x 12″
(I went to Home Depot and had them cut one 8 foot 3/4 x 9 inch piece of white birch into (2) 32″ pieces and (1) 16″ piece. You can use any type of wood you like. It was $12. I had a 2×4″ at home that I used for the bottom support.)

 

FIRST step was to attach the 16″ piece to the 32″ piece

 

 


I pre-drilled the center hole first and put the screw in. Then I did the other two. On each of the holes I drilled I also used a countersink drill bit so the screws are flush with the wood.

NEXT was to attach the front 32″ piece. I first measured 16 1/2 inches up made a mark, then found the center, drilled a hole and inserted the screw just enough so I could line it up with the other seat piece. Once the two pieces were lined up I inserted the screw all the way in and then inserted two other screws each side.

 

 

The next step was to insert the bottom support. I measured, cut, then screwed the 2×4″ to the underside of the horse.

 


 

AND that’s pretty much it! I spent more time writing this post then building the horse, it only took about a 20 minutes.  I added a little piece of wood to act as a stopper for a drawing board or canvas holder. Next I will sand the horse down to remove any rough areas or possible splinter issues. You can stain or paint the horse and even put a coat of polyurethane on it just to make it nice and last longer.

There are many ways to make a horse this is just one, the key are the dimensions it has to be 32″ long and tall. If you get the proportions wrong the horse can flip up if you sit too far towards the back.  I used screws and no glue so I can take it apart if I need to travel with one or more.

 

The finished Horse

 

I decided to Stain the horse and seal the wood with polyurethane. 

 

(here is how I use the horse to sit and draw or stand and paint)

 


 

Lucy approved.

 


 

 



Comments

8 Responses to How to Build a Drawing Horse

Just made one like yours, really helps me feel more professional when I draw heads which is what I am focusing on. Drawing the Asaro and Reilly heads as well as sculpting busts.
Thanks,

I made one today for my daughter using 3/4" plywood. It turned out great and she was very happy with it. I added a 30" x 24" drawing board made from 1/4" hardboard. I used a router to round over the edges to make it more comfortable to sit on and I used shallow grooves (cut with either table saw our router) to give her the ability to choose what angle she wants for the drawing board. Thanks for the dimensions; that's exactly what I was looking for!

What is that beautifully large palette that you're using (bottom left photo)? I'm just curious if you made that also. It looks wonderful!

Here and I realize this is OCD but how far back to the center of the stop for the drawing board? I realize it's a matter of preference.....and how did you finish it ?using stain with polyurethane? Mine is coming along_made mine with red oak.....also, just my two cents- don't use drywall screws they snap too easy esp with hardwood! Thanks!

Really nice project and thank you for the dimensions. I saw some pictures of 100 year old artists benches from Chouinard Art Institute and this looks just like them. Thanks.

How far back did you put the little piece that goes across to hold the board up? 6"-8"? I've seen some with grooves too instead of the piece sticking up. Do you have a preference (and why)? Thank you for these plans. Hope to build one this weekend!

Exactly what I was lokking for, thank you very much

I remember using drawing horses at Lawrence University. Today I built one with my uncle and it was precious quality time spent together. Thank you so much for sharing the information!


Leave a Comment

Remember Your Info
Check this box if you want email updates when people comment on this post